PEX PRO PEX B

Cross-linked polyethylene, commonly abbreviated PEX, XPE or XLPE, is a form of polyethylene with cross-links. It is used predominantly in building services pipework systems, hydronic radiant heating and cooling systems, domestic water piping, insulation for high tension (high voltage) electrical cables, and baby play mats. It is also used for natural gas and offshore oil applications, chemical transportation, and transportation of sewage and slurries. PEX is an alternative to polyvinyl chloride (PVC), chlorinated polyvinyl chloride (CPVC) or copper tubing for use as residential water pipes.

Properties

Low-temperature impact strength, abrasion resistance and environmental stress cracking resistance can be increased significantly by crosslinking, whereas hardness and rigidity are somewhat reduced. Compared to thermoplastic polyethylene, PEX does not melt (analogous to elastomers) and is thermally resistant (over longer periods of up to 120 °C, for short periods without electrical or mechanical load up to 250 °C). With increasing crosslinking density also the maximum shear modulus increases (even at higher temperatures).^[1][2] PEX has significantly enhanced properties compared with ordinary PE.

Almost all PEX used for pipe and tubing is made from high-density polyethylene (HDPE). PEX contains cross-linked bonds in the polymer structure, changing the thermoplastic to a thermoset. Cross-linking is accomplished during or after the extrusion of the tubing. The required degree of cross-linking, according to ASTM Standard F876, is between 65% and 89%. A higher degree of cross-linking could result in brittleness and stress cracking of the material, while a lower degree of cross-linking could result in product with poorer physical properties.

PEX has significantly enhanced properties compared to ordinary PE.^[3] This is due to the introduction of crosslinks in the system, which can significantly improve the chemical, thermal, and mechanical properties of the polymer.^[4] While HDPE and PEX both display increases in the initial tangent modulus and yield stress under temperature or strain-rate increases when undergoing compression, HDPE tends to exhibit flow behavior after reaching a higher yield stress and PEX tends to exhibit strain-hardening after reaching its slightly lower yield stress.^[5] The latter exhibits some flow behavior but only after reaching higher true strains. The behavior observed in PEX is also mimicked by the thermoplastic ultra-high molecular weight polyethylene (UHMWPE). However, PEX displays a stronger temperature and strain-rate dependence than UHMWPE. Additionally, PEX is notable for its high thermal stability. It displays improved creep behavior (i.e. resists creep deformation) and maintains high strength and hardness at very high temperatures compared to thermoplastic polyethylene.^[6]

PEX-A (PE-Xa, PEXa)

PEX-A is produced by the peroxide (Engel) method. This method performs “hot” cross-linking, above the crystal melting point. However, the process takes slightly longer than the other two methods as the polymer has to be kept at high temperature and pressure for long periods during the extrusion process. The cross-linked bonds are between carbon atoms.

PEX-B (PE-Xb, PEXb)

The silane method, also called the “moisture cure” method, results in PEX-B. In this method, cross-linking is performed in a secondary post-extrusion process, producing cross-links between a cross-linking agent. The process is accelerated with heat and moisture. The cross-linked bonds are formed through silanol condensation between two grafted vinyltrimethoxysilane (VTMS) units, connecting the polyethylene chains with C-C-Si-O-Si-C-C bridges.

PEX-C (PE-Xc, PEXc)

PEX-C is produced through electron beam processing, in a “cold” cross-linking process (below the crystal melting point). It provides less uniform, lower-degree cross-linking than the Engel method, especially at tube diameters over one inch (2.5 cm). When the process is not controlled properly, the outer layer of the tube may become brittle. However, it is the cleanest, most environmentally friendly method of the three, since it does not involve other chemicals and uses only high-energy electrons to split the carbon-hydrogen bonds and facilitate cross-linking.